|Size||Buy 2||Buy 3+||Buy 5+||Buy 8+|
A1 Pond Paint - Waterproof Paint for Pools and Ponds
Antel A1 Pond Paint is a universal water based epoxy resin coating, designed for easy and safe application. A1 Pond Paint possesses most of the properties of conventional epoxy resins with many additional advantages, particularly its tolerance of damp application conditions. A1 Pond Paint is applied in the same manner as ordinary emulsion paint and dries quickly to form a tough, easily cleaned coating, providing a waterproof barrier. The coating is non toxic, resistant to oil, and most mild chemicals. Subsequent over coating can be carried out after the original surface has been thoroughly degreased and cleaned.
The scope of applications for A1 Pond Paint is extensive and it can be used virtually anywhere that concrete or masonry requires protection or waterproofing. Suitable waterproof paint for pools and ponds.
A two part product available in 1, 2.5 and 5 litres. Non-returnable containers.
Store in a cool, dry and frost free area in original containers. Protect from freezing. Keep out of the reach of children. A shelf life in excess of 12 months can be expected for unopened containers kept in the above conditions.
5. DRYING & CURING
At 20 degrees C and with reasonable ventilation, the coating is touch dry in 6 hours and hard dry in 12 hours. Maximum cure, hardness and chemical resistance is obtained within 7 days.
Every litre of pond paint will cover approximately 6-7 squared metres (based on a non porous, smooth surface), however this will vary depending on how thickly you apply the material and also how porous the surface is.
If you are unsure on the porosity of the surface, we recommend you buy a little more than you think you will need to ensure you don’t run out of paint part way through the application.
7. CLEANING EQUIPMENT
When using spray equipment a thorough rinsing with cold water every hour will prevent a build up of cured material. Brushes and rollers should be washed with cold water and detergent and rinsed thoroughly in cold water.
Clean your pond to ensure a sound surface for the A1 Pond Paint to be applied to. If there are any leaks, these should be repaired with Antel Waterstop, Antel Epoxy Putty or Antel SBR Bonding Agent before applying the A1 Waterproof Paint. If unsure, please contact us for technical advice.
All voids and surface imperfections must be carefully filled especially when using Antel A1 Pond Paint Clear. (See note Ref 1).
A1 Pond Paint can be applied to Fibreglass after mechanically sanding the surface.
The performance of the coating can be seriously impaired if the following instructions are not strictly adhered to.
The pot life is approximately 1.5 hours. This is based on a temperature of 20 degrees C/68 degrees Fahrenheit. If you are applying the paint in higher temperatures, the pot life may be reduced. The material will become unworkable once outside of this pot life.
Once mixed, it is only possible to apply a single coat. Do not attempt to return to the mix to apply a second coat.
For simplicity we would recommend getting a separate pack of A1 Pond Paint for pools and ponds for each coat. However, if you would like to buy just the one pack for both coats, you will need to accurately divide the resin and hardener packs equally and mix in a separate container for each of the coats. We suggest you divide the packs by volume in a measuring jug to ensure accuracy.
WARNING – DO NOT APPLY IN TEMPERATURES BELOW 10 DEGREES C/50 DEGREES FAHRENHEIT AND ENSURE THERE IS AT LEAST A 4 HOUR WEATHER WINDOW.
PRODUCT CAN BE APPLIED IN MILDLY DAMP CONDITIONS BUT WILL NOT TOLERATE STANDING WATER.
1. Clean your pond to ensure a sound surface for the A1 Pond Paint to be applied to. If there are any leaks, these should be repaired with Antel Waterstop, Antel Epoxy Putty or Antel SBR Bonding Agent before applying the A1 Pond Paint. If unsure, please contact us for technical advice.
2. Pour the contents of the smaller container into the larger container and mix thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed.
3. Apply the first coat by brush, roller or spray. If the temperature is above 20 degrees C/68 degrees Fahrenheit, wait 6 hours before applying the second coat. If the temperature is below this, wait a full 24 hours before applying the next coat.
4. Apply the second coat of A1 Pond Paint.
5. After applying the second coat, wait 4-6 days (depending on temperature) before refilling your pond.
9. HEALTH & SAFETY
A1 Pond Paint is much safer to handle than other resin systems, however, it is recommended that all skin contact is avoided and that any areas of contact are washed immediately with soap and warm water. It is advisable to use a barrier cream and gloves when applying.
FOR FULL DETAILS PLEASE REFER TO HEALTH & SAFETY DATA SHEET.
NOTE REF 1
Antel A1 Pond Paint – Clear
With the formulation of the emulsion the mixture will take on a milky colour. This milkiness will gradually disappear during the curing cycle provided that the coating is not too thickly applied nor allowed to fill holes in the surface area of the application. If either of these situations does occur the milkiness will not disappear. All voids or surface imperfections must be carefully filled prior to any application of Clear A1 Pond Paint.
Antel A1 Pond Paint is available in a variety of colours. Please enquire for details.
To buy A1 Pond Paint please click here, select the quantity and colour you require and click add to basket, thank you.