£73.46
Size
Buy 2
Buy 3+
Buy 5+
Buy 8+
5 Litre
£79.31
£76.80
£75.13
10 x 310ml Cartridges
£69.83
£67.62
£66.15
£64.68
Technical Data Sheet
PROPERTY PROFILE
Highly effective ready-to-use cream emulsion on a silane/siloxane base for masonary injection against rising damp.
Pure Cream Technology
Its unique formulation on a pure cream emulsion base enables superior penetration of the active ingredient within the building material.
Cream Consistency
The unique cream consistency allows horizontal application techniques without the injection agent running out. This combined with superior stability in the borehole ensures the optimal penetration of the active ingredient in all directions.
Effective and Safe Protection against Rising Damp
Highly effective formulation enables long lasting and deep penetration of the mortar layer creating a horizontal barrier against rising damp.
Universal Use
Aida Injection Cream allows the effective treatment of alkaline and pH neutral as well as acidic building materials.
Solvent free (VOC free)
Aida Injection Cream is free from VOC (volatile, organic compounds) classified solvents.
Environment-friendly
Aida Injection Cream is ecologically safe and non-hazardous.
Straightforward Installation
Efficient installation by drilling the mortar joint and filling boreholes using a low pressure sprayer or a cartridge gun. No electric DPC pump required.
Controllable and Consistent Consumption Rates
The controlled installation technique ensures effective treatment and consistent consumption rates.
Proven Performance
Application in practise, independent research and test reports have proven its effectiveness.
BBA Certificate No. 05/4202.
Does not form salts
Characteristic data of the product in the packaged state:
Active ingredient content: approx. 10% by mass
Density: approx. 0.84 kg/l
Consistence: cream
pH value neutral
Flash point > + 100°C
Range of use:
procedures, particularly for fair faced brickwork, slim masonry layers and cleaved masonry, in- and outdoors. The mortar layer turns into a horizontal isolation. In case of higher moisture content, the Remmers patented thermal convective drying method is to be used prior to the injection procedure. Alternatively a low-pressure injection is recommended.
Working directions
Pressureless injection
Drill 12mm diameter holes horizontally into the mortar joint, in general into the joint intersections, at 120mm centres and to a depth of 10-20mm from opposite face. Remove bore dust from the hole and fill with Aida Injection Cream using a low pressure sprayer or a cartridge gun.
Low pressure injection
In the low pressure procedure, the injection cream is applied into the mortar joint, in general into the joint intersections, at 120mm centres and to a depth of 10-20mm from opposite face using drive-in, resp. screw packers (metal packers) at max. 5 bar for application in a wall thickness up to 13½" and at max. bar 7 for application in a wall thickness in excess of 13½". Recommended equipment is a low pressure sprayer with suitable manometer and flowmeter.
Effect
The capillary active building material causes the injection cream to break into a liquid phase. The silane/siloxane ingredient reacts with water and becomes a polysiloxane. During the reaction process, a silane vapour phase is produced that causes excellent penetration.
Flanking measures
Salt contaminated plasterwork should be renewed. Please ask for our recommended Funcoil 1lr Restoration Render re-plastering specification.
Tools/equipment, cleaning
a) Drilling equipment e.g. helix drill, or SDS Plus or SDS Max drill
b) Injection equipment, e.g. low pressure sprayer or cartridge gun
Clean tools and equipment while the material is fresh with water.
Packaging, application rate and storing:
Packaging
310 ml and 1 litre plastic cartridges, 5 litre plastic bucket
Application rate (pressureless injection)
Wall thickness 110mm 220mm 330mm 440mm
Borehole depth 100mm 200mm 310mm 420mm
Borehole diameter 12mm 12mm 12mm 12mm
Application rate 0.9ltrs 1.9 ltrs 2.9 ltrs 3.9 ltrs
Per 10mm wall
length
Shelf life:
At least 1 year unopened, original stored cool but frost-free.
Storing temperature between +5°C and +25°C
Safety, ecology, disposal:
Further information concerning safety during transport, storage and handling as well as for disposal is found in
the Safety Data Sheet.
Technical information
Flanking measures
Salt contaminated plasterwork should be renewed. Please ask for our recommended Funcoil 1lr Restoration Render re-plastering specification.
Tools/equipment, cleaning
a) Drilling equipment e.g. helix drill, or SDS Plus or SDS Max drill
b) Injection equipment, e.g. low pressure sprayer or cartridge gun
Clean tools and equipment while the material is fresh with water.
Packaging, application rate and storing:
Packaging
310 ml and 1 litre plastic cartridges, 5 litre plastic bucket
Application rate (pressureless injection)
Wall thickness 4½"(110mm) 9"(220mm) 13½"(330mm) 18"(440mm)
Borehole depth 100mm 200mm 310mm 420mm
Borehole diameter 12mm 12mm 12mm 12mm
Application rate 0.9 litres 1.9 litres 2.9 litres 3.9 litres
Per 10m wall
Length
Application rates for porous, rubble or highly absorbent masonry may vary.
Shelf life:
At least 1 year unopened, original stored cool but frost-free.
Storing temperature between +5°C and +25°C
Safety, ecology, disposal:
Further information concerning safety during transport, storage and handling as well as for disposal is found in the latest Safety Data Sheet.
