Next Day Delivery Available On Most Orders

Free Mixer Paddle on all Pool/Pond Paint orders over £100

Notice - We now sell a range of Water Based Epoxy Coating in a Matt finish. See below for details.

Waterbased Epoxy Coating - Standard Finish

Waterbased Epoxy Coating - Matt Finish

Antel Water based Epoxy Coating is a universal water based epoxy resin coating designed for easy and safe application. Water based Epoxy Coating possesses most of the properties of conventional epoxy resins with many additional advantages, particularly its tolerance of damp application conditions. It is applied in the same manner as ordinary emulsion paint and dries quickly to form a tough, easily cleaned coating, providing a vapour barrier. The coating is non toxic, resistant to oil, and most mild chemicals. Subsequent over coating can be carried out after the original surface has been thoroughly degreased and cleaned.

2. USES

The scope of applications for Waterbased Epoxy Coating is extensive and it can be used virtually anywhere that concrete or masonry requires protection or waterproofing.

Recommended areas and types of use :-

1. Wall coating in areas of food manufacture and storage.
2. Tank lining for protection against mild chemicals.
3. Waterproofing and decorative finish for all brick, concrete, cement, masonry and asbestos surfaces.
4. As a general weatherproofing and waterproofing coating.
5. For application to damp surfaces where other paints cannot adhere.
6. As a finish for swimming pools.
7. As a membrane to prevent rising damp in floors.
8. As a sealing coat for asbestos containing materials.
9. Wet rooms.

Typical locations :-

1. Swimming pools.
2. Water tanks/sewage treatment plants.
3. Abattoirs.
4. Dairies/milking parlours, food factories, breweries.
5. Grain silos.
6. Basement/damproof membrane.
7. Chemical industry garages.
8. Bunds and water plants.
9. Wet rooms.

3. PACKAGING

A two part product available in 1, 2.5 and 5 litres. Non-returnable containers.

4. STORAGE

Store in a cool, dry and frost free area in original containers. Protect from freezing. Keep out of the reach of children. A shelf life in excess of 12 months can be expected for unopened containers kept in the above conditions.

5. DRYING & CURING

At 20 degrees C and with reasonable ventilation, the coating is touch dry in 6 hours and hard dry in 12 hours. Maximum cure, hardness and chemical resistance is obtained within 7 days.

6. COVERAGE

Every litre of Water Based Epoxy Coating will cover approximately 6-7 squared metres (based on a non porous, smooth surface), however this will vary depending on how thickly you apply the material and also how porous the surface is.

If you are unsure on the porosity of the surface, we recommend you buy a little more than you think you will need to ensure you don’t run out part way through the application.

7. CLEANING EQUIPMENT

When using spray equipment a thorough rinsing with cold water every hour will prevent a build up of cured material. Brushes and rollers should be washed with cold water and detergent and rinsed thoroughly in cold water.

8. PREPARATION

Although Water based Epoxy will over coat most other finishes and paints, the best results are achieved when surfaces are clean and free of other finishes/coatings. All surfaces should be damp dry or at least not subject to running water. Particularly attention should be made to degreasing surfaces before application. All voids and surface imperfections must be carefully filled especially when using Water based Epoxy Clear. (See note Ref 1).

8.1 MIXING
The performance of the coating can be seriously impaired if the following instructions are not strictly adhered to.

Stir the contents of the larger tin. Pour the entire contents of the smaller container into the larger container making sure to scrape out as much as possible and mix thoroughly using a mechanical mixer. When the mix is complete it is advisable to mix/stir for a further 2-3 minutes to ensure complete dispersion of the 2 components.

NOTE: - Because the coating is a chemically engineered system with two components which react, the coating has a pot life duration. The pot life is the time the applicator has to apply the coating before it becomes unusable. The pot life for this coating is 1.5 hours at 20 degrees C. Warmer temperatures will reduce the pot life of the coating.

8.2 APPLICATION STEPS

WARNING – DO NOT APPLY IN TEMPERATURES BELOW 10 DEGREES C/50 DEGREES FAHRENHEIT AND ENSURE THERE IS AT LEAST A 4 HOUR WEATHER WINDOW.

PRODUCT CAN BE APPLIED IN MILDLY DAMP CONDITIONS BUT WILL NOT TOLERATE STANDING WATER.

For simplicity we would recommend getting a separate pack of Water Based Epoxy Coating for each coat. However, if you would like to buy just the one pack for both coats, you will need to accurately divide the resin and hardener packs equally and mix in a separate container for each of the coats. We suggest you divide the packs by volume in a measuring jug to ensure accuracy.

1. Clean the surface you will be applying the Water Based Epoxy Coating to. If there are any leaks, these should be repaired with Antel Waterstop, Antel Epoxy Putty or Antel SBR Bonding Agent before applying the Water Based Epoxy Coating. If unsure, please contact us for technical advice.

2. Pour the contents of the smaller container into the larger container and mix thoroughly (ideally with a mixer paddle) for a minimum of three minutes, so that the two components are completely mixed.

3. Apply the first coat by brush, roller or spray. If the temperature is above 20 degrees C/68 degrees Fahrenheit, wait 6 hours before applying the second coat. If the temperature is below this, wait a full 24 hours before applying the next coat.

4. Apply the second coat.

9. HEALTH & SAFETY

Water based Epoxy coating is much safer to handle than other resin systems, however, it is recommended that all skin contact is avoided and that any areas of contact are washed immediately with soap and warm water. It is advisable to use a barrier cream and gloves when applying.

FOR FULL DETAILS PLEASE REFER TO HEALTH & SAFETY DATA SHEET.

NOTE REF 1

Antel Water based Epoxy – Clear

With the formulation of the emulsion the mixture will take on a milky colour. This milkiness will gradually disappear during the curing cycle provided that the coating is not too thickly applied nor allowed to fill holes in the surface area of the application. If either of these situations does occur the milkiness will not disappear. All voids or surface imperfections must be carefully filled prior to any application of Clear Waterbased Epoxy. Antel Waterbased Epoxy is available in a variety of colours. Please enquire for details.